Autosensing: music starts as soon as a signal is detected
Plug in, play, done.
Turntable, TV, games console or CD player: many sources are connected to a trivum device by cable. So you don't have to select them in the app every time, all trivum line inputs feature Autosensing. As soon as an audio signal arrives at an input, the trivum system detects it and takes care of the rest.
How it works.
When trivum detects a signal at the input, it switches on the assigned zone and selects the input as the source. If music from another source is already playing in the zone, it switches to this input. You simply put the record on or switch on the TV, and the sound comes out of the speakers in the room. No app, no button presses, no detours.
When the signal ends, trivum can also tidy up again: after an adjustable waiting time, the zone switches off or returns to the previously heard source.
Typical uses.
In the living room, the TV sound plays automatically through the ceiling speakers as soon as the TV is switched on, and falls silent again when it's switched off. The turntable in the study plays as soon as the needle drops. In hospitality venues or shops, an external background music player starts in the right zone every morning without any further action. And anyone connecting their laptop by cable hears the sound in the room straight away.
Perfect with the TV: fixed volume for the TV input.
When watching TV, you have the TV remote in your hand and want to control the volume with it too. For this, a fixed start volume can be set for each line input. When the zone switches to the TV input, trivum sets exactly this volume, and trivum's own volume control is locked. The TV alone then determines loud and quiet. When you switch to another source, you decide what happens to the volume: it stays as it is, returns to the previous value, or jumps to a fixed volume. This way there are never two volume controls getting in each other's way, and the music doesn't suddenly start at TV volume after watching television.
How to set it up.
Open the setup of your trivum system in your browser at http://<IP address>/setup and go to Player → Line inputs. There, select the input you want. All settings apply only to this input.
In the Auto sensing options section, you set up Autosensing:
- Enable autosensing switches the function on for this input.
- Action to run when signal is detected defines what happens when a signal is detected, for example Power on an output, i.e. switching on a zone.
- Output to be powered on when signal is detected determines which zone is switched on, for example "Living Room".
- Auto ungroup when grouped automatically removes the zone from a group, so the TV sound doesn't suddenly play in other rooms too.
- Restore source when music stops switches back to the previously heard source once the signal ends, or switches the zone off again if Autosensing had switched it on.
- Activation volume (in %) is the threshold above which a signal counts as "music is playing".
- Sensing timeout is the waiting time in seconds after which the zone switches off again if there's no signal. This way, short pauses between two songs don't immediately cause it to switch off.
To find the right threshold, the Current signal volume display at the bottom of the page is helpful. It shows the current level at the input. Check the value once when the source is off or in standby, and once when it's playing, and set the Activation volume somewhere in between. Some devices produce a slight background noise even in standby, which would otherwise be mistakenly detected as a signal.
You set the volume for switching to the input and back in these two sections:
- Action on Line Input start → Use fixed start volume: with Start volume (in %) you define the volume the zone plays at when switching to this input.
- Volume change on Line Input stop: here you choose what happens when switching to another source. Do not change leaves the volume unchanged, Restore recent volume restores the volume from before the switch, and Use fixed stop volume sets it to the value under Stop volume (in %). This value applies globally to all line inputs.
Tip: The level of the input itself can be adjusted under Level adjustment. First use Line input volume adjust, the gain in the hardware. Zone volume adjust is only intended for when that's not enough.
Developed from practical experience.
Autosensing isn't an add-on, but part of every trivum system. The function has grown out of 25 years of experience with multiroom installations, from exactly the situations customers encounter in everyday life.
Which devices support Autosensing?
All trivum devices with a line input, for example M2, SC344m, RP321 and RP311v2.